DASAPLANO 0,01 connect

Airtightness membrane for roof retrofits from the outside, with self-adhesive strips

Advantages

Simple implementation of the airtightness layer: installation across rafters and insulation
Dry and well-protected building structures thanks to active moisture transport
Protection during the construction phase: suitable as a temporary covering
Made-to-order cutting and bonding service available
Quick and reliable adhesion thanks to the integrated ‘connect’ self-adhesive strips along the membrane strips
Excellent values in hazardous substance testing, has been tested according to the ISO 16000 evaluation scheme

Areas of application

For use as an airtightness membrane that can be subjected to outdoor exposure on roof retrofits from the outside in the case of full packing of the existing spaces between the rafters with insulation. Installation across the rafters, underneath an additional layer of over-rafter insulation consisting of wood-fibre underlay panels. Please contact Technical Support at pro clima in Germany for assistance with calculating the thickness of the external wood-fibre insulation that is required from a building physics viewpoint.

Also available as a pre-fabricated sheet for your roofing project in Germany, Switzerland, Austria, France, the Netherlands and Belgium with the pro clima made-to-order cutting and bonding service!

Installation instructions

Installation steps

Installation instructions

General conditions

DASAPLANO 0,01 connect is to be installed with the printed side facing the installation technician. The membrane is to be installed horizontally (parallel to the eave) in a taut manner, covering over the compartment insulation.

If DASAPLANO 0,01 connect is subject to outdoor exposure or rain, the membranes must be installed perpendicular to the water run-off direction. This will ensure better protection of the building structure against moisture penetration.
To avoid condensation formation, the thermal insulation cover should be installed immediately after airtight adhesion of DASAPLANO 0,01 connect. This applies particularly to work carried out in winter.

Airtight seals can only be achieved on vapour control (alternate terms: vapour check or retarder) membranes that have been fitted with no folds or creases.

A normal indoor residential climate is present for the entire duration of the roof refurbishment work.

Note: Please contact Technical Support at pro clima in Germany for assistance with calculating the thickness of the external wood-fibre insulation that is required from a building physics viewpoint.

Made-to-order membranes for roof projects: Cutting and bonding service for underlay and airtightness membranes

Make your roofs weathertight and airtight even more quickly and easily

Are you planning to use pro clima membranes on an upcoming roof project? If so, you no longer need to worry about bonding the individual lengths of membrane to each other and cutting them to size to fit your roof surface. You can now order many pro clima membranes already cut and bonded to match your roof surface! As part of this service, SOLITEX WELDANO 3000 roofing underlay membranes are welded together in the workshop, and SOLITEX MENTO 3000/5000 connect, SOLITEX QUANTHO 3000 connect, INTELLO X connect, DA connect and DASAPLANO 0,01 connect are joined using their self-adhesive strips.

In this way, pro clima takes care of the preparation of underlay and airtightness membranes for your roof project in an automated, tailored and precise manner at a reasonable price. You will be able to install reliably sealed roof structures more efficiently, even if your roof geometry demands more complicated shapes. This made-to-order pre-fabrication service saves valuable installation time on site and also makes you less dependent on weather conditions.

This service is currently available in Germany, Switzerland, Austria, France, the Netherlands and Belgium.

Advantages

Time savings due to shorter installation period on site
No additional finishing work required: made-to-order membranes are delivered that fit your roof surface perfectly
The underlying building structures remain dry: prepared sheeting provides immediate protection in adverse weather conditions
High-quality end products thanks to assembly under protected conditions in the workshop
Efficient installation thanks to technical support from pro clima

How does this service work: It's this easy ....

1. Tell us the shape and dimensions of your roof surface

a. Define the roof type

What type of roof is involved? Is it a gable roof, a single-pitched roof, a tented roof, etc. Please specify the geometrical form of the roof and provide an outline sketch of the roof with actual lengths and surface areas.

b. Specify any special geometries

Please specify any special geometries such as valleys, roof dormers, skylights etc. The absence or presence of such features will determine whether the resulting pre-fabricated sheet will be a standard geometry (2D and rectangular) or a special geometry (2D non-rectangular, 2D rectangular with additional sections).

c. Specify the eave and bargeboard lengths

Please specify in your drawing the dimensions of the bargeboards and eaves and all dimensions – e.g. valley lengths – to be taken into account in determining the surface area.

d. Specify the ridge position and water run-off direction

Please indicate on your drawing the position of the ridge with a line and the water run-off direction with a direction arrow.

e. Specify the starting position and roll-out direction (longitudinal and perpendicular)

The prepared sheet is generally delivered to your building site as a package that is rolled up in two directions.

Have you planned a specific roll-out starting position, direction and sequence? If so, please mark this position with a cross. Ideally, you should indicate the sequence of roll-out directions with arrows and sequential numbering (1, 2).

e. Specify the starting position and roll-out direction (longitudinal and perpendicular)

f. Additional services

Marking/cutting of skylights
Marking/cutting of any additional penetrations (vent pipes etc.)
Marking of counter battens

In order to be able to provide these services, we need you to send us .dwg or .dxf files and complete our order and inquiry form, which is available here

2. Production of the pre-fabricated sheet and shipping

Once you have placed an order, the individual lengths of membrane will be stuck or welded together, as appropriate, and cut to size for your specific roof project. If required, the positions of the counter battens, skylights and any other penetrations can be marked.

The prepared sheet is then rolled up, placed on a pallet and shrink-wrapped for shipping. We aim to deliver to your site within 10 days of the order being placed for delivery locations in Germany, Austria, France, the Netherlands and Belgium.